TM 55-2815-574-24
SUSTAINMENT MAINTENANCE
ENGINE
CRANKSHAFT AND STABILIZER REMOVAL, CLEANING, INSPECTION, REPAIR, AND INSTALLATION
INITIAL SETUP:
Tools and Special Tools
Equipment Condition (cont.)
General mechanic's tool kit
Air inlet collector assembly removed (WP 0104)
(WP 0179, Table 1, Item 130)
Turbochargers removed (WP 0114)
Chain hoist (WP 0179, Table 1, Item 65)
Exhaust manifolds removed (WP 0157)
Chemical gloves
Marine gear oil cooler removed
(WP 0179, Table 1, Item 52)
(TM 55-2040-211-24)
Dial indicator (WP 0179, Table 1, Item 67)
Blower drive shaft and spring removed (WP 0109)
Hand hammer (dead blow)
Fuel cooler removed (WP 0082)
(WP 0179, Table 1, Item 59)
Air box covers removed (WP 0036)
Industrial goggles (WP 0179, Table 1, Item 54)
Air box drains removed (WP 0037)
Shackle, 3/4 in., 4.75 ton
Starting motor removed (WP 0164)
(WP 0179, Table 1, Item 116)
Lube oil dipstick tube assembly removed
Sling, 5,300 lb 6 ft (green)
(WP 0179, Table 1, Item 118)
Overspeed governor removed (WP 0169)
Socket wrench set, 3/8 in. sqdr.
Marine gear oil cooler mounting bracket removed
(WP 0179, Table 1, Item 135)
Strain gage (WP 0179, Table 1, Item 50)
Lube oil cooler removed (WP 0128)
Torque wrench, 075 in-lb
Engine mounted on stand (WP 0033)
(WP 0179, Table 1, Item 140)
Fresh water cooling system bypass hoses
Torque wrench, 1/2 in. drive,
removed (WP 0143)
0175 ft-lb (0335 Nm)
Cylinder head poppet valve rocker arm covers
(WP 0179, Table 1, Item 143)
removed (WP 0049)
Torque wrench, dial 3/8-in. drive, 100600 ft-lb
Electronic governor actuator rod removed
(136814 Nm) (WP 0179, Table 1, Item 139)
Universal puller kit
Governor actuator removed (WP 0098)
(WP 0179, Table 1, Item 99)
Fuel pump removed (WP 0095)
Wire scratch brush (WP 0179, Table 1, Item 21)
Air intake housing removed (WP 0103)
Blower drive shaft removed (WP 0112)
Blower removed (WP 0110)
Materials/Parts
Heat exchanger removed (WP 0134)
Ball (and roller bearing grease
Fresh water cooling system starboard thermostat
WP 0178, Table 1, Item 22)
housing removed (WP 0140)
Cleaning compound (WP 0178, Table 1, Item 9)
Fresh water cooling system port thermostat
Crankshaft and stabilizer
housing removed (WP 0141)
(TM 55-1925-205-24P, 0201)
Fuel injector control tube and lever removed
(
Engine lubricating oil, 30W
WP 0178, Table 1, Item 25)
Flywheel housing removed (WP 0072)
Pipe plug Qty: 4 (WP 0180, Table 1, Item 109)
Vibration dampener removed
Wiping rag (WP 0178, Table 1, Item 30)
Cylinder heads removed (WP 0047)
Lube oil pan removed (WP 0127)
Lube oil pressure regulator valve removed
Personnel Required
Engineer 88L
Lube oil pressure relief valve removed (WP 0125)
Equipment Condition
Crankcase breather limiter assembly removed
0061-1